threadModeler

threadModeler

coolOrange s.r.l.

Digitally signed app

무료

OS:
언어:

설명

The threadModeler tool has been developed to allow Autodesk® Inventor® users to generate a realistic modeled equivalent thread based on an existing Inventor thread feature. Users are able to select an existing thread feature in the model, which the threadModeler then converts to a realistic 3D modeled thread based on the underlying thread feature properties.

 

Modeled threads are accurately generated saving a lot of time and effort for the user when compared with a manual approach, bringing a higher degree of realism to your models.

 

Please watch this short video for an overview of the threadModeler.

도움말 문서 읽기

이 버전 정보

버전 19.0.8, 2020-05-26
Support of Inventor 2020 Note: coolOrange will not further develop the app or provide new versions for newer Inventor versions. The threadModeler for Inventor 2020 is the last version, which is published here. We reserve the right to remove the App from the Autodesk App Store at any time.

스크린샷 및 비디오


고객 리뷰

(172 리뷰)

|

기술 도움말 보기
  • Just what I was looking for
    Thomas Comita | 10월 03, 2020 다운로드 확인 (이것은 무엇입니까?)

    This feathur is long overdue in Inventor, SoldWorks has had it now for years.

    I would like Autodesk to put thread cutting option into the Hole command, label the options:  SHADED THREAD, MODELED THREAD.


  • Version 19.0.8, 5/26/2020
    Darrell Kemp | 9월 23, 2020 다운로드 확인 (이것은 무엇입니까?)

    I contacted CoolOrange regarding backwards compatability of the latest version as it did not work on my installation of Inventor 2013. Manuel got back to me with a possible workaround, which I tried and after a bit of fiddling I've managed to get it working. For more info go and have a look at https://coolorange.atlassian.net/wiki/spaces/THREAD/pages/846430210/FAQ+threadModeler.


  • The best Add-in Is Finally working
    Fawzi Harami | 9월 02, 2020 다운로드 확인 (이것은 무엇입니까?)

    Working Fine on 2021


  • threadMldeler
    w z | 8월 13, 2020 다운로드 확인 (이것은 무엇입니까?)

    Works perfectly in inventor 2021. Thank you!


  • Does not Work with Tapered Thread
    Ron Dietel | 8월 06, 2020 다운로드 확인 (이것은 무엇입니까?)

    Be advised that the coolOrange App does not work with tapered thread (e.g., NPT thread). Regards.


  • 2021
    Alicia Clark | 6월 21, 2020 다운로드 확인 (이것은 무엇입니까?)

    As others have said, to get it to work with 2021 simply navigate to this file:  open c:\ProgramData\Autodesk\ApplicationPlugins\coolOrange_threadModeler.bundle\Contents\coolOrange.ThreadModeler.Inventor.addin and edit <SupportedSoftwareVersionLessThan> (you can use notepad) and change the line <SupportedSoftwareVersionGreaterThan>21..</SupportedSoftwareVersionGreaterThan>

      <SupportedSoftwareVersionLessThan>26..</SupportedSoftwareVersionLessThan>

    Restart the program and itll load in!


    Stuart Wood | 6월 29, 2020

    Thankyou ! You are a life saver.


    Patrick Drabik | 7월 15, 2020

    I have Inventor 2021 and I made the changes in notepad and saved them. It still does not work for me. Any advice?


    Tor Re | 7월 28, 2020

    Works perfectly in inventor 2021. Thank you!


    Ahmad Asmandar | 8월 18, 2020

    you are the best thank you


    Heiko Schedletzky | 8월 25, 2020

    Funktioniert Danke


    Brian Bischoff | 9월 21, 2020

    This worked for me! Thanks


    Owen Sullivan | 10월 15, 2020

    where do I find this at, is it in Inventor somewhere or on my PC?


    Vitaly Golovko | 10월 16, 2020

    Thank you!!!


    Robbie Johnson | 10월 20, 2020

    This info would have been useful to note: if you cannot see the c:\ProgramData folder, go to Control Panel, then Appearance & Personalization, then Folder Options. Click the "View" tab and make sure the bullet that says "Show Hidden Files & Folders" is selected. After you click Apply it will show up.


  • We need Threadmodeler
    Luigi Monaco | 6월 15, 2020 다운로드 확인 (이것은 무엇입니까?)

    Would Autodesk please put this peanuts coding in their official product. It saves a lot of time in 3D printing, we need this funkctionality. Does someone listen/ read, please confirm.


    Martijn Peters | 8월 10, 2020

    To my knowledge they have this functionality in Fusion 360, which is free to use for hobbyists.


  • Impossible to make a pinch with a decimal
    Pierre Adam | 6월 06, 2020 다운로드 확인 (이것은 무엇입니까?)

    All the videos I've seen people can do thread pitch with a decimal. That simply does not work for me on inventor 2020...

    Does someone know how to do it ? Is there a configuration somewhere ?

    I basically can't do a M3x0.5 or M4x0.8. It just doesn't let me. Doesn't even offer an other pitch.

    If I try to go a M10x1.5, that pluging replace the 1.5mm pitch with a 1.0mm

    Thanks for your answers !


  • Version 2021
    Gerald Leto | 6월 04, 2020 다운로드 확인 (이것은 무엇입니까?)

    Honestly, I am not savvy at any of this, not a programmer, engineer and can barely use this software. That said, it worked for me in version 21 by making the following changes. 

      <SupportedSoftwareVersionGreaterThan>21..</SupportedSoftwareVersionGreaterThan>

      <SupportedSoftwareVersionLessThan>26..</SupportedSoftwareVersionLessThan>


    Sai Mallipedhi | 6월 10, 2020

    Where did you make these changes?


    Kim Verwiel | 6월 27, 2020

    worked for me to. had to change both 20 and 25 to 21 and 26. thanks. changes are made here . go to this file C:\ProgramData\Autodesk\ApplicationPlugins\coolOrange_threadModeler.bundle\Contents. then open ''coolOrange.ThreadModeler.Inventor.addin'' in notepad and change the numbers as stated above.


  • version 2021
    Victor Cherkasov | 5월 24, 2020 다운로드 확인 (이것은 무엇입니까?)

    for 2021 open c:\ProgramData\Autodesk\ApplicationPlugins\coolOrange_threadModeler.bundle\Contents\coolOrange.ThreadModeler.Inventor.addin and edit <SupportedSoftwareVersionLessThan>


    Maxwell Richhart | 6월 01, 2020

    I see: <SupportedSoftwareVersionLessThan>25..</SupportedSoftwareVersionLessThan> What do I change the value to for 2021? Thank you!


    Eric Willard | 6월 02, 2020

    is there a way to make this work with 2021?


  • How do I get it to work in 2021?
    Jeffrey Chapman | 5월 18, 2020 다운로드 확인 (이것은 무엇입니까?)

    How do I get it to work in 2021?  I gave it a 5 since I know you will solve this problem ;)


  • Update
    Lucas Abate | 5월 17, 2020 다운로드 확인 (이것은 무엇입니까?)

    2021 version would be great.


    Cool Orange (게시자) | 5월 26, 2020

    coolOrange will not further develop the app or provide new versions for newer Inventor versions. You can find the source code for the threadModeler on a public GitHub repository: https://github.com/coolOrangeLabs/inventor-thread-modeler


  • Update needed for Inventor 2021
    Raj Ramoutar | 5월 01, 2020 다운로드 확인 (이것은 무엇입니까?)

    Can you guys get this working with Inventor 2021 please.Thanks.


    Sarskisiuzk Ctlechops | 5월 16, 2020

    +1


    Victor Cherkasov | 5월 24, 2020

    edit file "coolOrange.ThreadModeler.Inventor.addin" <SupportedSoftwareVersionLessThan>


    Cool Orange (게시자) | 5월 26, 2020

    coolOrange will not further develop the app or provide new versions for newer Inventor versions. You can find the source code for the threadModeler on a public GitHub repository: https://github.com/coolOrangeLabs/inventor-thread-modeler


  • Best Add On for Inventor ( for me anyway )
    Stuart Wood | 4월 29, 2020 다운로드 확인 (이것은 무엇입니까?)

    Thread Modeller is a fantastic app, which makes adding realism to my models ( for my client to see ) so much easier. But when is the 2021 version arriving ?


  • Best
    Stéphane AGEA | 4월 20, 2020 다운로드 확인 (이것은 무엇입니까?)

    Very Best plugin

    ThreadModeler no longer works on Inventor 2021, is it possible to have an upgrade?

    Thank's


  • Best
    Scrablertt Scrablertt | 4월 09, 2020 다운로드 확인 (이것은 무엇입니까?)

    Thanks a very useful addition. Please make support 2021


    Jjgolff Jjgolff | 4월 16, 2020

    Pasame tu correo electronico.


  • Só funciona em roscas feitas com o comando 'Rosca' em cilindros e furos, não funciona em roscas feito com o comando 'Furo'
    Airton Dos Santos Lima | 4월 01, 2020

    Muito bom o app mas é preciso corrigir este problema.


  • Should Be A Standard Plug-In
    Joseph Bongiorno | 1월 21, 2020 다운로드 확인 (이것은 무엇입니까?)

    Works great and is easy to use. However, I would like to see additonal templates added besides ISO and BSW. I use this feature primairly to display threads on my stl files for 3D printing instead of manually making my threads. Definitley a time saver.


  • hen nb!
    磊 张 | 11월 19, 2019 다운로드 확인 (이것은 무엇입니까?)

    you juxing luowen gongju jiu geng hao le ( ̄▽ ̄)"


  • Works good
    Georgi Kalchev | 9월 04, 2019 다운로드 확인 (이것은 무엇입니까?)

    It's very nice program. Works great with metric profile but I needed to make ISO trapezoidal tread and didn't recognise it.


  • OTTIMO
    M P | 5월 22, 2019 다운로드 확인 (이것은 무엇입니까?)

    Con Inventor 2019 lavora molto bene ottimo


  • not sufficient for 3d Printing
    Nathan Villines | 4월 15, 2019 다운로드 확인 (이것은 무엇입니까?)

    Tried using this to easily 3D print something with male and female threads. Their modeler doesn't have any tolerance for male to female and did not work. 


    Joshua Yates | 12월 04, 2019

    This does work but you have to add in your own clearance, allow 0.3mm or more depending on your printer. For example if your external thread is on a shaft of 25mm, the internal hole for the thread diameter needs to begin at 25.3mm, then use the thread feature and the coolorange tool which would will a gap of 0.15mm all the way around. increase the gap until it works with your printer.


  • Inventor 2019.3
    Karel Cedivoda | 3월 07, 2019 다운로드 확인 (이것은 무엇입니까?)

    Today I tried it in Inventor 2019. It function. For interior thread it is necessary to make the hole and thread have you make extra.

    Nice :)


    Stefan Maier | 2월 02, 2020

    I also use Inventor 2019. When i have a M10 interior thread, after transformation with thread modeler it´s a M8! At first i build the hole and after that the thread. What is my mistake? Do you have a solution? Regards Stefan


  • Не для Чертежей
    Дмитро Паденко | 1월 11, 2019 다운로드 확인 (이것은 무엇입니까?)

    Добрый день! Эта надстройка для тех, кто занимается графикой,  или на рендеринг конечной модели...для разработки КД не годится, не отображает в чертеже резьбу, а так штука интересная.


  • Good but could be so much better
    Kirk Arthur | 12월 05, 2018 다운로드 확인 (이것은 무엇입니까?)

    Thanks for this useful app.... To bad Inventor does not give us the option to model the threads like Fusion360.  A few things could make it better, like... make it associative so that if I later change the thread size in the hole, the modeled thread feature also updates. Also, don't add the coil feature to a seperate solid.

    For those that want ANSI (UNF AND UNC) just use the ISO template.  It will give the correct thread model.


  • Awesome, but better if UNC, UNF thread included
    Zhifei Deng | 11월 12, 2018 다운로드 확인 (이것은 무엇입니까?)

    At titled


  • Support of tapped holes?
    Ko-Keng Chang | 10월 02, 2018 다운로드 확인 (이것은 무엇입니까?)

    Thank you for the useful tool.

    Is it popssible to turn tapped holes into modeled thread?


  • Very good, needs additional threads.
    Tony Macias | 8월 20, 2018 다운로드 확인 (이것은 무엇입니까?)

    It would be great if UNC, UNF, and NPT thread forms were supported. This is the one improvement I can think of making.


  • Awesome...
    Sebastien Bolle | 6월 30, 2018 다운로드 확인 (이것은 무엇입니까?)

    Except there is no support for ACME threads. I would love to see that added in a future release.


  • Muy bueno.
    Sebastian Lopez Rubio | 5월 30, 2018 다운로드 확인 (이것은 무엇입니까?)

    Perfecto y fácil de usar


  • Wow this is amazing.
    Isaacrbeam Isaacrbeam | 5월 18, 2018 다운로드 확인 (이것은 무엇입니까?)

    Very simple to use and amazing tool. Thanks for the development. Keep up the good work.


  • Maravilloso
    Danaes Arcos | 4월 23, 2018 다운로드 확인 (이것은 무엇입니까?)

    Fácil de intslar y aplicar, Genial¡¡¡


  • Wonderful
    Jzhu C | 3월 14, 2018 다운로드 확인 (이것은 무엇입니까?)

    Thanks alot


  • Super
    Josef Novák | 3월 12, 2018 다운로드 확인 (이것은 무엇입니까?)

    Perfektní appka :) .... Perfect app. THANK YOU very much :)


  • Exactly what I wanted from Inventor.
    Perrin Zahn | 1월 21, 2018 다운로드 확인 (이것은 무엇입니까?)

    Amazing. The app is small, making it easy to download just about anywhere, the installation takes seconds, and the thread-converting process is intuitive and easy to do. I literally can't think of anything else I'd want from this add-on.


  • Great tool!
    Lars Van Der Wal | 1월 07, 2018 다운로드 확인 (이것은 무엇입니까?)

    Use it for 3D printing. Thanks :-)


  • worked for small threads
    Fra H | 12월 06, 2017 다운로드 확인 (이것은 무엇입니까?)

    It actually worked great for a 3/8" nc thread, but did not work for a 7/16" nc thread.


  • good
    Ricardo Aleman | 11월 27, 2017 다운로드 확인 (이것은 무엇입니까?)

    good


  • Excellent Plug-in for 3d Prints
    Sotiris Katsikis | 11월 19, 2017 다운로드 확인 (이것은 무엇입니까?)

    This is an excellent plugin to enable 3D printing of threads.


  • Great for 3d printing
    Michael Berna | 10월 23, 2017 다운로드 확인 (이것은 무엇입니까?)

    I use this for converting the built in thread representations to 3d printable objects. This saves me a lot of time and ensures an accurate thread.


  • Perfect idea and very decent plug-in.
    臧 晓晗 | 10월 13, 2017 다운로드 확인 (이것은 무엇입니까?)

    I like it and I support your plug-in and YouTube channel. By the way, I'm Chinese. LoL


  • Thread annotation
    Katarina Goreta | 9월 25, 2017 다운로드 확인 (이것은 무엇입니까?)

    how to annotate this thread in drawing for machine operator, I tried but wont let me to annotate!?


  • WOW! Works Great
    Dan Murphy | 8월 17, 2017 다운로드 확인 (이것은 무엇입니까?)

    Click on the tool. Click on the tread file and boom! Saved me a lot of time instead of doing it manually.


  • 3d Printing
    Iain Mcmurray | 8월 16, 2017 다운로드 확인 (이것은 무엇입니까?)

    Amazing and simple to use. Perfect for setting up my models for 3d Printing when I need threads.


  • Perfect!!!
    Johann Hepp | 8월 10, 2017 다운로드 확인 (이것은 무엇입니까?)

    Works better than expected. Relieve the work. Thank you!


  • Great tool
    Brad Headlam | 8월 08, 2017 다운로드 확인 (이것은 무엇입니까?)

    Time saver if you need to fully model the thread. Only downside is creates large file size, but still great.


  • Works good, a few issues
    Frank Okipnak | 8월 04, 2017 다운로드 확인 (이것은 무엇입니까?)

    As everyone else is saying, great for the most part, just needs to be refined so can do more thread styles as well as holes properly. Otherwise, very handy and cool. The error I get the most is "Failed, try with a bigger pitch offset value", no matter what I try, does not work.


  • Super
    Sule Wad | 8월 01, 2017 다운로드 확인 (이것은 무엇입니까?)

    A great Tool


  • Hoze
    Jozsef Sallai | 7월 29, 2017 다운로드 확인 (이것은 무엇입니까?)

    Hi there, As others have already thanked I also want to do: Thank you guys!


  • easy app to use
    Julian Shepherd | 7월 13, 2017 다운로드 확인 (이것은 무엇입니까?)

    really easy to use great results .


  • Works good
    Ben Vinck | 6월 26, 2017 다운로드 확인 (이것은 무엇입니까?)

    It does what's supposeed to do. Nothing more. Nothing less.


  • Excelente!
    Luis Carlos Vega Renteria | 6월 25, 2017 다운로드 확인 (이것은 무엇입니까?)

    Muy buena aplicacion! Yo te sugiero que hagas un pequeño tutorial de como hacer roscas para NPT ya que creo que nadie sabe como hacerlo. Gracias


  • good
    谢 凡 | 6월 12, 2017 다운로드 확인 (이것은 무엇입니까?)

    it works very good,especially for 3D print.Thank you!


  • Straightforward and Effective
    Jonathan Bazak | 6월 09, 2017 다운로드 확인 (이것은 무엇입니까?)

    Does exactly what I needed it to do: make matching 3d-printable threads on holes and surfaces with just a handful of clicks. Support for more non-standard ISO metric threads would be cool, but there are plenty here as-is. Very handy extension to have!


  • good
    Waiman Liu | 6월 06, 2017 다운로드 확인 (이것은 무엇입니까?)

    very good. i can 3d print many gears now !!


  • Absolutely amazing
    Giacomo Brugnolo | 5월 24, 2017 다운로드 확인 (이것은 무엇입니까?)

    Very useful for 3d printing and making your components look absolutely better!


  • Awesome
    Ricardo Fernandez Saavedra | 5월 15, 2017 다운로드 확인 (이것은 무엇입니까?)

    Works perfectly! Thank you!


  • Can't be used with .idw callouts
    Douglas Reiland | 5월 14, 2017 다운로드 확인 (이것은 무엇입니까?)

    The downloading and aesthetics of threadModeler are fine, but, unfortunately, this application is not compatible with .idw drawings. Inventor does not recognize the threadModeler modifications to the .ipt, therefore they cannot be called out with hole/thread specifications on drawings. I submitted this to coolOrange tech support. They acknowledged that this was a problem and acted as though this was the first time anyone raised this issue with them.


  • VERSION
    Daniel Gamarra | 4월 30, 2017 다운로드 확인 (이것은 무엇입니까?)

    I downloaded the plugin. The installation was successful but i can't see the app in the ribbon. Is it working in version 2018??


  • Worked perfect so far
    Simon Roth | 4월 27, 2017 다운로드 확인 (이것은 무엇입니까?)

    Had no problems with it, created perfect threads for 3d printing. Thank you


  • Very Useful
    Jordan Coquoz | 4월 18, 2017 다운로드 확인 (이것은 무엇입니까?)

    I don"t normally rate things but I wanted to give this five stars because of how amazingly useful this is. Huge thanks to the developers of this tool.


  • Cool so far
    Engineer Draft | 4월 12, 2017 다운로드 확인 (이것은 무엇입니까?)

    Have used it once where I wanted to really expose thread on a drawing, so that immediate clarification would happen. Worked well and was happy, good in context of time saving for those one off type jobs.


  • Works well for me
    Jonathan Colella | 4월 10, 2017 다운로드 확인 (이것은 무엇입니까?)

    No hassle, as advertised


  • Great app needs a few tweeks
    ROGER HOOKER | 3월 29, 2017 다운로드 확인 (이것은 무엇입니까?)

    it's very responsive, however it's difficult to champher and seemingly impossible to extrude through.


    Fazeel Tahir | 6월 13, 2019

    did you get any solution for this?


  • Version 2020
    Rodolfo Ramos Castelo Branco | 6월 18, 2015 다운로드 확인 (이것은 무엇입니까?)

    Good afternoon, for the 2020 version, is it already under development? Thank you

맨 위로 이동